|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I found my Clarion VRX8370R in the Camper I bought and I wasn't able for month to understand it.
The Owner Manual was perfect and just what I was searching for.
Thank you.
Leonardo
;
Very good copy of Manual, clear and easy to print off, arrived very promptly and reasonably priced.
Thanks, I will use you again.
;
Zeer duidelijke afdrukken op A4-formaat , zeer uitgebreide handleiding . Pluspunt ,zeer snelle
respons van jullie , binnen de 24h . Top !!!
;
I AM HIGHLY IMPRESSED BY THE EASE OF USE OF THIS DOWNLOAD SERVICE. INSTRUCTIONS ARE CLEAR AND SIMPLE TO FOLLOW....EVEN BY TECHNOPHOBES SUCH AS MYSELF. THE EMAILS POINT YOU IN THE RIGHT DIRECTION...ITS SO EASY PEASY. THE DOWNLOAD CHOICE OF USER MANUALS IS EXTENSIVE AND I COULD NOT FIND A CHEAPER OR MORE EFFICIENT SERVICE ON THE INTERNET. I COULD NOT HAVE MADE A BETTER CHOICE OF INFORMATION PROVIDER. SHOULD I EVER NEED ANOTHER USER MANUAL, THEN THIS IS THE FIRST CHOICE SITE. COULD NOT BE BETTER PLEASED!!!!!!!...MANY THANXES FROM JIM BURNS
;
I was impressed with the quality of service (frequent e-mails to let you know the status of your order), and the speed at which the download became available. The manual was a life saver and was not easy to track down. Thank you for such an excellent service.
APPLICATIONS
BASIC SETTINGS We recommend setting the controls as indicated in the following three sections. This will give you a better idea of the switch and control functions: 1. Set the MSE-100A channel (1 or 2) to bypass mode (the mode switch OUT and the red LED lit). Set the LOW Mix and the TUNE center position and the PROCESS controls fully counterclock wise. Turn the MIX controls fully CCW and press the IN/OUT switch (green IN LED lit). Now turn the LOW MIX controls counterclockwise from the center position and the HIGH MIX controls slowly clockwise until the fundamental bass and high frequencies become more emphasized and the sonic image begins to �open up� or to �widen�. The quality of the sound enhanced signal can be adapted to the program material by varying the LOW MIX controls and the TUNE controls. 3. Check your settings by making an A/B comparison using the IN/OUT switch.
2.
SOUND ENHANCEMENT DURING RECORDING The sound enhancing effect can be increased by using the MSE-100A, not only during replay, but during actual recording. This method of sound processing is recommended, in particular, if the subsequent storage medium is of poor quality. When doing tape duplications, the enhancer signal added during the recording will compensate for the loss in quality which occurs when several generations of copies are subsequently made from the master tape. In this scenario, insert the MSE-100A directly after the master output of the mixer into the recording path of the master or multi-track machine. Set up the unit as described above in �Sound Enhancement During Replay�. In particularly difficult cases, we recommend using the MSE100A both during both recording and replay.
3.
When using enhancers or exciters, it is easy to get carried away. Therefore, we recommend regular A/B comparisons (IN/OUT) while setting the controls, in order to constantly check the signals integrity. Rule of thumb: the enhancer�s effect should only be noticeable when it is lacking, but not when it is present! Listening at high volume levels over long periods (in studios, for example) leads to listening fatigue and thus reduces sensitivity to higher frequencies. Regular pauses keep your hearing �healthy� and helps you avoid exaggerated sound processing. SOUND ENHANCEMENT DURING REPLAY For this application, the MSE-100A follows the master or multi-track recorder, i.e., inserted between tape machine and mixer (or amplifier). Of course, a cassette recorder, or similar equipment can also be used as a signal source. If a companding noise reduction system is used in this situation, it should precede the MSE-100A.
Using the MSE-100A during recording
Using the MSE-100A in a mixer send/return loop
Using the MSE-100A during replay
1. 2.
Set up your equipment as usual, with the effects switched off. Turn on the MSE-100A and adjust the controls as desired (if necessary, read above �Basic Settings� once again).
8
ENHANCING THE SOUND OF EFFECTS DEVICES Often, signal processing units such as flangers, phasers, distortion, chorus, delay and reverb units etc. considerably limit the signal�s sound quality. Here too, the MSE-100A will be of help. Simply inset the unit after the effects device. If there are several devices, insert the MSE-100A as the last unit in the chain.
|
|
|
> |
|
